Detailer Tip: Stopping Creaky Door Noises

One of the most common complaints with late model cars are door noises like creaks, squeaks or rattle noise from the doors.  It can sound like a “crack” when crossing driveways and often can often get worse after the car is detailed.

Once the usual suspects like loose and broken trim are ruled out dealerships and workshops are often at a loss to explain the noise let alone remedy it.

What causes Creaky Door Noises?

The noise we hear is actually caused by part of the door seals design and material that’s meant to reduce noise!  When you look at your door seals you’ll see they are made up of a number of parts.  The main cause of the noise is the outermost “flap” that serves to reduce wind noise and also act as an initial barrier to dust and water.

Door Seal Flap
Outer door seal “flap” circled.

On the inside the seal has a “flocked” or “felted” finish which is the cause of the noise.

Why?  Well I’ve heard a lot of reasons and the most common is that as manufacturers strive to reduce costs of cars the quality of finishes like these suffer, this results in the fibres not being as long, plush or effective as intended.

Instead the fibres stick and release with movement of the door.  This appears to worsen after waxes or sealants are applied to the paintwork in the area of these seals.

How do we address it?

There’s three possible solutions:

  1. Replace the seals:  BMW for example has a number of replacement seals available that are used by dealerships to address the noise when raised as warranty complaints.  Anecdotally the replacement seals have a plusher finish and resolve the issue.
    I doubt this is cost effective for owners and most manufacturers will not have a revised part.
  2. Lubricate the seals: As detailers this is the easiest approach requiring a small addition to our “tool kit” and requiring only a few minutes of our time.  While this is not a permanent solution it can be incorporated into the regular wash process and remains very cost effective.
  3. Add lubrication to the body:  This fix is now used by BMW and other manufacturers to provide a long-term fix.  It involves laying a low-friction self-adhesive strip around the door openings where the flocking would normally contact the bodywork.

Lubricating Flocked Door Seals

There are a number of products of varying prices that can used for the job.  My preference is for a simple Paraffin Wax stick which does the job, costs next to nothing and doesn’t have any risk of marking clothing or hands if touched.

Really when deciding on a product you want two things – a “dry” finish and a product that doesn’t mark or discolour clothing when brushed against.

Gummi Pflege, Teflon Sprays, Dri-Lube, Silicone Sprays all will work – however they only last 3-4 weeks.

Goss Dri-Lube
Goss Dri-Lube is my goto for creaky door seals

My goto is Goss Dri-Lube, a stick of paraffin wax that is applied much like a crayon

Applying Goss Dri-Lube
Applying Goss Dri-Lube to creaky Renault door seals

As you can see in the photo I’m applying a generous layer over all the flocked parts of the seal.  In warm weather the whiteness “melts” away quickly eating the fibre and stopping the creaking door noises!

But what if that doesn’t work?

While in most cases lubricating the flocked door seals will resolve the door noises there are cases where it doesn’t work.

Bentley has this particular issue on some models which is resolved by adding lubrication under the seals where they attach/fit to the door.

For this a Silicone Grease is used, and simply smeared between the rubber of the seal and the door.  To do this I’d use a spray pack of silicone grease and the tip to get between the seal and body and then massage around the door.

What about a permanent solution?

The most cost effective solution thats likely to last long term is to apply a Teflon tape around the door openings where the flocking contacts the body.

The recommended tape is 3M “5430” Squeak Reduction Tape which is best described as specialised and has a specialised price tag of AUD187 for a 33m roll of 25.4mm width.

 

Published by

Aaron

Geek, Car Guy, Former entrepreneur looking for the next big thing while doing the things I should have done 20 years ago. Key pusher and thinker for a large organisation who dreams to be doing something else.

Leave a Reply